Cannot figure out the wiring between the Innovate LM-2 to S60, please help.
If i connect LM-2 Analog Out 1 + (Lime green) to Pin 19 and Ana Out 1 - (Yellow) to Pin 33 then AFR 22,39 is displayed at Real Time Info, engine not running.
If i swap the wires it shows AFR 7,35.
If no wire connected to Pin 33, does not make any difference in readings.
If i start the engine the needle on virtual AFR gauge bouncing all over the place,..
What am I doing wrong?
Innovate LM-2 wiring
-
- Posts: 68
- Joined: Fri Feb 01, 2019 4:36 pm
- ECU Model: S80 Pro
- Firmware Version: 6500
Re: Innovate LM-2 wiring
Does your engine idle smoothly?
If your map is all over the pace, the AFR will be as well.
Mine is showing 22 on KOEO, and are a little bit up and down on idle wich I believe is normal, but my map needs fine tuning on idle aswell.
Manual for the LM2: https://www.innovatemotorsports.com/sup ... Manual.pdf
If your map is all over the pace, the AFR will be as well.
Mine is showing 22 on KOEO, and are a little bit up and down on idle wich I believe is normal, but my map needs fine tuning on idle aswell.
Manual for the LM2: https://www.innovatemotorsports.com/sup ... Manual.pdf
-
- Posts: 1622
- Joined: Fri Feb 28, 2014 1:03 pm
- ECU Model: S40 Pro
- Distributor: DTA
- Firmware Version: 79
Re: Innovate LM-2 wiring
Wiring sounds correct.gigford wrote:Cannot figure out the wiring between the Innovate LM-2 to S60, please help.
If i connect LM-2 Analog Out 1 + (Lime green) to Pin 19 and Ana Out 1 - (Yellow) to Pin 33 then AFR 22,39 is displayed at Real Time Info, engine not running.
If i swap the wires it shows AFR 7,35.
If no wire connected to Pin 33, does not make any difference in readings.
If i start the engine the needle on virtual AFR gauge bouncing all over the place,..
What am I doing wrong?
Have you set the lambda input controller to Innovate?
If so, open Real Time Mapping, and monitor your input voltage there.
Re: Innovate LM-2 wiring
The car has not been mapped at mid-high rpms yet, have not taken out to test drive. Only set the fuel/iginition up to 1500rpm using LM-2 controller.
At idle the engine runs smoothly cold or hot, so i can say it's stable.
The LM-2 displays fairly constant AFRs at idle, so no bouncing as in Real TIme Info.
Even with the engine off and i do a calibration so the LM-2 shows 20.9 as it should the DTA shows the max AFR of 22,39.
Yes, I choose the Lambda controller input to Innovate at first time.
Can i measure the input voltage between the two wires using a multimeter?
A plan to make a video and upload here.
At idle the engine runs smoothly cold or hot, so i can say it's stable.
The LM-2 displays fairly constant AFRs at idle, so no bouncing as in Real TIme Info.
Even with the engine off and i do a calibration so the LM-2 shows 20.9 as it should the DTA shows the max AFR of 22,39.
Yes, I choose the Lambda controller input to Innovate at first time.
Can i measure the input voltage between the two wires using a multimeter?
A plan to make a video and upload here.
-
- Posts: 1247
- Joined: Thu Jul 28, 2011 4:10 am
- ECU Model: S100 Pro
- Distributor: None-Coil On Plug :)
Re: Innovate LM-2 wiring
you should be able to connect your pc to the innovate also to read directly if you think something is wrong, you may need 2 pc's to look at the dta also.