Hi,
trying to set the throttle stops with a Magneti Marelli PF09 sensor(Cosworth yb) but run out of ideas...
Sensor o/p(middle pin) is connected to pin 34 S60 and the outer ones to 5V and sensor gnd(pin 33).
It shows the throttle is fully open even if i swap the ground/5V:
If i open the throttle, the throttle position is keep staying above 1000, the virtual blade does not move at all.
I have two of these sensors one is a new one the other is used, but the results are the same.
If i tick the reverse tps box, the green "current ecu map" switches to red "map not current"
Thanks for any help in advance!
Magneti Marelli PF09 TPS help!
-
- Posts: 3586
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: Magneti Marelli PF09 TPS help!
It's unlikely both are faulty....so that means most likely your wiring is incorrect.
And initially ignore the throttle position, as that applies after the main/max stops are set.
What does the voltage readout say ? Does it change with position ?
And initially ignore the throttle position, as that applies after the main/max stops are set.
What does the voltage readout say ? Does it change with position ?
Re: Magneti Marelli PF09 TPS help!
Voltage readout is the same 4995mV, does not change with throttle movement, even if the 5v/ground swapped.
If i disconnect the plug it shows 0mV and the blade jumps back to zero.
Plug disconnected, the measurement shows 5V present between the outher pins. I also did continuity check on all 3 pins to the ecu sensor plug and all ok.
If i disconnect the plug it shows 0mV and the blade jumps back to zero.
Plug disconnected, the measurement shows 5V present between the outher pins. I also did continuity check on all 3 pins to the ecu sensor plug and all ok.
-
- Posts: 1250
- Joined: Thu Jul 28, 2011 4:10 am
- ECU Model: S100 Pro
- Distributor: None-Coil On Plug :)
Re: Magneti Marelli PF09 TPS help!
Get your multi meter on to the TPS its self to verify the centre pin is the output, to do this look for ohms on the outer 2 pins you should see something like 2000 and this won't change when you move the device. Then connect the centre pin and one outer to the meter and you should get a variance when you move the device.
-
- Posts: 1622
- Joined: Fri Feb 28, 2014 1:03 pm
- ECU Model: S40 Pro
- Distributor: DTA
- Firmware Version: 79
Re: Magneti Marelli PF09 TPS help!
They are not compatible with our ECUs, as they have a logarithmic (possibly exponential, can't remember) output, and some strange input requirements.
You'll need to change them.
On the plus side, if they are known to be working, they sell for a (relative) small fortune as they are no longer made.
You'll need to change them.
On the plus side, if they are known to be working, they sell for a (relative) small fortune as they are no longer made.
Re: Magneti Marelli PF09 TPS help!
Damn...any suggestions what kind of TPS i should look for?Alex DTA wrote:They are not compatible with our ECUs, as they have a logarithmic (possibly exponential, can't remember) output, and some strange input requirements.
You'll need to change them.
On the plus side, if they are known to be working, they sell for a (relative) small fortune as they are no longer made.
Re: Magneti Marelli PF09 TPS help!
Pf01 not only a pot, but it has a microswitch it. It is standard for 2wd cossies and l6 marelli ecu. but i have never seen red pf09, only pf01. Please give me an email address in private message, because i can't reply to your previos priv message. It says "We are sorry, but you are not authorised to use this feature. You may have just registered here and may need to participate more to be able to use this feature." but I don't know why...
There are good infos here:
http://www.bigturbo.co.uk/main4.htm
There are good infos here:
http://www.bigturbo.co.uk/main4.htm
Re: Magneti Marelli PF09 TPS help!
2wd you cannot use. use a 4wd tps
the 2wd tps goes to open at idle. this is not ideal for any modern ecu
And as Alex said, the Cosworth Tps is not linear.
However i used it, and it works but if i had to do it all again , i would change to a commonly found tps(linear)
Warren
the 2wd tps goes to open at idle. this is not ideal for any modern ecu
And as Alex said, the Cosworth Tps is not linear.
However i used it, and it works but if i had to do it all again , i would change to a commonly found tps(linear)
Warren
Re: Magneti Marelli PF09 TPS help!
I am using 2wd tps with other standalone ECU, but turned a bit on the throttle to non switched region. It has oval holes for adjusting.
Re: Magneti Marelli PF09 TPS help!
Maybe have a look at TPS from:
Lancia integrale
Fiat Coupe 16v / 16v turbo
This use the same Weber TPS, but have different part numbers.
Lancia integrale
Fiat Coupe 16v / 16v turbo
This use the same Weber TPS, but have different part numbers.