STC DBW - Pin Outputs
-
- Posts: 29
- Joined: Mon Jul 16, 2012 8:31 am
- ECU Model: No ECU
- Firmware Version: 34
STC DBW - Pin Outputs
Hi, I am looking into the pin out puts for the below - these are not in the STC wiring diagram and i've had no luck with google searches
BMW Throttle Motor Part No. a2c53142839 E92 M3
Citroen C2 Throttle Pedal Part No. Bosch 0280752240
Thanks
Paul
BMW Throttle Motor Part No. a2c53142839 E92 M3
Citroen C2 Throttle Pedal Part No. Bosch 0280752240
Thanks
Paul
-
- Posts: 29
- Joined: Mon Jul 16, 2012 8:31 am
- ECU Model: No ECU
- Firmware Version: 34
Re: STC DBW - Pin Outputs
I have managed to find the BMW pin outs now, just the Citroen throttle pedal to go.
BMW
1 = Enable connection
2 = 12V / Terminal Bar 87
3 = Ground / Terminal bar 31
4 = Ident. connection
5 = Can Low
6 = Can High
7 = Sensor 1 / Analog
8 = Sensor 1 / Ground
9 = Sensor 1 / Supply 5V
BMW
1 = Enable connection
2 = 12V / Terminal Bar 87
3 = Ground / Terminal bar 31
4 = Ident. connection
5 = Can Low
6 = Can High
7 = Sensor 1 / Analog
8 = Sensor 1 / Ground
9 = Sensor 1 / Supply 5V
-
- Posts: 1250
- Joined: Thu Jul 28, 2011 4:10 am
- ECU Model: S100 Pro
- Distributor: None-Coil On Plug :)
Re: STC DBW - Pin Outputs
I think in the DTA instructions it asks to check with the office that the combination of these two devises is compatible with the STC,
-
- Posts: 1622
- Joined: Fri Feb 28, 2014 1:03 pm
- ECU Model: S40 Pro
- Distributor: DTA
- Firmware Version: 79
Re: STC DBW - Pin Outputs
E92 M3 won't work, it requires CAN bus information we don't have.
You can bypass that and just wire the STC directly to the motor, as it's identical to the one used in the S54.
I can't help with the Peugeot one.
You can bypass that and just wire the STC directly to the motor, as it's identical to the one used in the S54.
I can't help with the Peugeot one.
-
- Posts: 29
- Joined: Mon Jul 16, 2012 8:31 am
- ECU Model: No ECU
- Firmware Version: 34
Re: STC DBW - Pin Outputs
Thanks Alex, so just use the connections that are in the STC Manual for the BMW?Alex DTA wrote:E92 M3 won't work, it requires CAN bus information we don't have.
You can bypass that and just wire the STC directly to the motor, as it's identical to the one used in the S54.
I can't help with the Peugeot one.
-
- Posts: 1622
- Joined: Fri Feb 28, 2014 1:03 pm
- ECU Model: S40 Pro
- Distributor: DTA
- Firmware Version: 79
Re: STC DBW - Pin Outputs
BMW E46, yes, not BMW Mini.
-
- Posts: 29
- Joined: Mon Jul 16, 2012 8:31 am
- ECU Model: No ECU
- Firmware Version: 34
Re: STC DBW - Pin Outputs
Well, i have finally wired up all the bits today, but my laptop with Windows 10 won't connect to the STC controller, but my mates toughbook with RS232 and windows 7 it can connect.
Is this because i have windows 10?
Thanks
Paul
Is this because i have windows 10?
Thanks
Paul
-
- Posts: 3586
- Joined: Tue Aug 02, 2011 12:08 pm
- ECU Model: No ECU
- Location: Norn Iron
Re: STC DBW - Pin Outputs
more likely whatever USB adapter you're using, or how it's configured. Troublesome little buggers they are.
-
- Posts: 29
- Joined: Mon Jul 16, 2012 8:31 am
- ECU Model: No ECU
- Firmware Version: 34
Re: STC DBW - Pin Outputs
Thanks Stevie. I downloaded the latest drivers for the adaptor as well, but it still wasn’t having any of it.
I didn’t connect the STC can bus to the ecu, will this still allow us to step up the parameters in the stc software or will it stop stc working correctly?
I didn’t connect the STC can bus to the ecu, will this still allow us to step up the parameters in the stc software or will it stop stc working correctly?
-
- Posts: 1622
- Joined: Fri Feb 28, 2014 1:03 pm
- ECU Model: S40 Pro
- Distributor: DTA
- Firmware Version: 79
Re: STC DBW - Pin Outputs
W10 is fine. Check USB driver settings are correct.
Windows current USB driver doesn't work, so use the two guides in the downloads section of the website to sort them.
You can connect to the STC and sort all the basic settings without the CAN connected, but the throttle won't operate until it sees an ECU over the CAN connection.
Windows current USB driver doesn't work, so use the two guides in the downloads section of the website to sort them.
You can connect to the STC and sort all the basic settings without the CAN connected, but the throttle won't operate until it sees an ECU over the CAN connection.