ECUs can be unlocked by DTA.
Email office@dtafast.co.uk
Search found 1622 matches
- Fri Jan 26, 2024 10:51 am
- Forum: Software, Firmware, and Data Logging
- Topic: Unlock S40PRO
- Replies: 1
- Views: 1104
- Fri Nov 24, 2023 3:54 am
- Forum: General
- Topic: Using S60 without injectors
- Replies: 3
- Views: 4597
Re: Using S60 without injectors
No need to do anything, just disconnect the injectors.
- Fri Nov 24, 2023 3:53 am
- Forum: Sensors, Inputs, and Outputs
- Topic: RPM calculated gear to XDASH
- Replies: 6
- Views: 5092
Re: RPM calculated gear to XDASH
Thanks for the info Alex! Just back from a test ride. Engine RPM and Shaft RPM both shows 0 during speed. Where should I start looking? You need two speed sensors as a minimum. One goes to the left undriven wheel speed, and is used to calculate the vehicle speed. The second must go to either the Le...
- Wed Nov 22, 2023 3:44 am
- Forum: General
- Topic: dta s80 after car fire
- Replies: 7
- Views: 10517
Re: dta s80 after car fire
If you have amplified coils turned on, then the current draw is reasonable.
If not, then it's damaged.
If not, then it's damaged.
- Tue Sep 19, 2023 9:23 am
- Forum: Sensors, Inputs, and Outputs
- Topic: DTA T2 Airshifter Wiring
- Replies: 5
- Views: 4555
Re: DTA T2 Airshifter Wiring
The shift switch needs to be between Pin 11 (Digital #1) and Sensor Grnd - Pin #28 or #29. Gounding the switch activates a shift cut (however you have it set up. Note it can't be chassis or engine or DTA Power ground - only Sensor grnd. So if this a bike? and you are using something like the MRE el...
- Tue Sep 19, 2023 9:22 am
- Forum: General
- Topic: setting up full Seq S80 COP / twin plug "I am stuck again"
- Replies: 6
- Views: 4224
Re: setting up full Seq S80 COP / twin plug "I am stuck again"
The crank scope shows the TDC value to be around 66. The crank scope shows tooth 13, but 12 is less than 13, so it's either going to be 11 or 13. The scope is just the ECUs best guess; as stevieturbo says, confirm it with a timing light. The cam pulse is on tooth 43 on the other engine rotation from...
- Tue Sep 19, 2023 9:13 am
- Forum: Sensors, Inputs, and Outputs
- Topic: RPM calculated gear to XDASH
- Replies: 6
- Views: 5092
Re: RPM calculated gear to XDASH
The dash just reads the value from the ECU, so get the values in the ECU working, and the dash will just work. The dash value is Gear. In the first image, the values Engine RPM and Shaft RPM must show data for this function to work. The easiest way to get this set up is to put the car on axle stands...
- Tue Sep 12, 2023 11:13 am
- Forum: Wiring and Loom Building
- Topic: Pwm wiring
- Replies: 4
- Views: 3563
Re: Pwm wiring
That EWP does not need an external SSR, as that is built in to the water pump.
Wire it as per that wiring diagram, and it should work.
Wire it as per that wiring diagram, and it should work.
- Thu Aug 31, 2023 6:22 am
- Forum: Wiring and Loom Building
- Topic: Four wire round connectors anyone recognise?
- Replies: 6
- Views: 3445
Re: Four wire round connectors anyone recognise?
They look like Souriau bulkhead connectors
Re: BMW M42
Hello ok its a zetec coil , NGK R plugs the ht leads that came with it , no idea of make / model the crank wire runs up alongside the block , then through a plastic cover , then connects to the loom I do not know what you mean by "with the shield drained at the ECU end ?" sorry everything...