Cheers Stevie.
Alex is off till after Xmas, I'll check with him
when he's back.
Thanks for taking the time to reply & have a great Xmas.
Cheers
Andy
Search found 21 matches
- Thu Dec 23, 2021 10:39 am
- Forum: Wiring and Loom Building
- Topic: LSU 4.9 Sensor wiring
- Replies: 5
- Views: 6949
- Wed Dec 22, 2021 3:46 pm
- Forum: Wiring and Loom Building
- Topic: LSU 4.9 Sensor wiring
- Replies: 5
- Views: 6949
Re: LSU 4.9 Sensor wiring
Thanks Stevie.
I have that but wasn't sure about Pin 8 connector 3 VGND
Which pin on the 02 sensor is that?
Cheers
Andy
I have that but wasn't sure about Pin 8 connector 3 VGND
Which pin on the 02 sensor is that?
Cheers
Andy
- Tue Dec 21, 2021 11:26 am
- Forum: Wiring and Loom Building
- Topic: LSU 4.9 Sensor wiring
- Replies: 5
- Views: 6949
LSU 4.9 Sensor wiring
Hi Guys.
I need a little help wiring a LSU 4.9 wideband sensor into T series ECU
Do any of you guys know the pinouts for the ECU to the 02 sensor?
Cheers
Andy
I need a little help wiring a LSU 4.9 wideband sensor into T series ECU
Do any of you guys know the pinouts for the ECU to the 02 sensor?
Cheers
Andy
- Wed Dec 15, 2021 11:56 am
- Forum: General
- Topic: New ECU Series
- Replies: 17
- Views: 7110
Re: New ECU Series
Great, thanks Alex.
- Wed Dec 15, 2021 10:33 am
- Forum: General
- Topic: New ECU Series
- Replies: 17
- Views: 7110
Re: New ECU Series
Hi Alex. I'm building the loom for the T8 that we are fitting to a 3.2 Carrera Porsche 911 with Jenvey Heritage intake. I have a map for this engine configuration but using an S80 Pro ECU. Will this map work in the T8 providing all of my engine configuration settings in General Engine settings 1 and...
- Tue Oct 26, 2021 4:56 am
- Forum: General
- Topic: COP problem
- Replies: 7
- Views: 3587
Re: COP problem
Just to update I removed the COPs and refitted the original single coil and HT leads. The engine started and ran fine so I left it like that since my last post. Last week I decided to revisit the COP setup. I made a completely new harness, taking a lot of care to make sure the wiring was spot on. Th...
- Sun Jul 25, 2021 4:28 pm
- Forum: General
- Topic: COP problem
- Replies: 7
- Views: 3587
Re: COP problem
Loss of comms only after the engine has started and ran for a few seconds.
12v supply while cranking is good
nothing from the ecu output either un plugged or plugged in. I have yet to check with a scope
as I need to bring it from work tomorrow.
12v supply while cranking is good
nothing from the ecu output either un plugged or plugged in. I have yet to check with a scope
as I need to bring it from work tomorrow.
- Sun Jul 25, 2021 2:09 pm
- Forum: General
- Topic: COP problem
- Replies: 7
- Views: 3587
Re: COP problem
Thanks for the reply Stevie.
When I run a coil test I have nothing from no1 output
I'm running 2000us dwell for the outputs
Loss of communication happens every time I start the engine.
I'm thinking that I should just send Alex the ECU so that he can check it.#
What do you think?
When I run a coil test I have nothing from no1 output
I'm running 2000us dwell for the outputs
Loss of communication happens every time I start the engine.
I'm thinking that I should just send Alex the ECU so that he can check it.#
What do you think?
- Sun Jul 25, 2021 7:14 am
- Forum: General
- Topic: COP problem
- Replies: 7
- Views: 3587
COP problem
I've just fitted R8 COP's to an air cooled 911 engine and have run into a problem. The ECU is an S80 and prior to the COP's I was running Jenvey ITB's and a single coil with the original distributor. I removed the HT leads and dizzy cap, wired the COP's as per instructions. pin 1 to ign 12v pin 2 to...
- Fri Jan 31, 2020 3:46 am
- Forum: Sensors, Inputs, and Outputs
- Topic: MAP sensor for non turbo application
- Replies: 6
- Views: 5554
Re: MAP sensor for non turbo application
Thanks Guys.