Search found 58 matches

by Andy-reid
Sun Sep 11, 2022 6:45 am
Forum: General
Topic: Flat shift and paddle shift
Replies: 4
Views: 4813

Re: Flat shift and paddle shift

so a flat shift switch will still work even if it is also the paddle up? input so both systems work?
by Andy-reid
Sun Apr 17, 2022 6:12 am
Forum: General
Topic: S100 paddle, launch and traction questions
Replies: 17
Views: 16984

Re: S100 paddle, launch and traction questions

can the values be inverted in the dta software?
by Andy-reid
Sun Apr 17, 2022 5:29 am
Forum: General
Topic: S100 paddle, launch and traction questions
Replies: 17
Views: 16984

Re: S100 paddle, launch and traction questions

new problem i had the car at rolling road for a quick tidy up on my s100 with latest firmware my problem is i have an AEM cd7 dash with gear display all set was ok until i got car back from rollers he did say the raw voltage for the gearbox pot is wrong and my display in the AEM is all wrong but my ...
by Andy-reid
Thu Sep 24, 2020 6:44 pm
Forum: Sensors, Inputs, and Outputs
Topic: aux in / paddle setup
Replies: 15
Views: 11612

Re: aux in / paddle setup

Quick update! the Flappy paddle setup is awesome! it almosts sounds like an auto from front and just a quick pop at the rear takes about 0.2 of a second to shift gear and power restored! nor a single missed gear! flat shift is un believable blip on down needs a bit dialing as it is a bit jerky! just...
by Andy-reid
Thu Sep 24, 2020 6:32 pm
Forum: General
Topic: S100 road speed
Replies: 1
Views: 2768

S100 road speed

Hi! on my S100 when testing at a race track testing the Flappy paddle setup i noticed no speed displayed on my dash! for some reason the ecu is not seeing the omron proximity sensor on the diag setup?the sensor lights up when the target tooth is in place the question is can i make the ecu use my un ...
by Andy-reid
Sun May 24, 2020 4:32 pm
Forum: Sensors, Inputs, and Outputs
Topic: aux in / paddle setup
Replies: 15
Views: 11612

Re: aux in / paddle setup

Well. Actuator fitted and valve plumbed and tested. It seems to be on down shift it blips and does an ignition cut if that is possible ? As I get a pop from the exhaust too I am awaiting a spring return blipped so I only need 1 pipe to engine bay as everything I'd under the dash
by Andy-reid
Mon May 18, 2020 3:42 am
Forum: Sensors, Inputs, and Outputs
Topic: sensor info
Replies: 17
Views: 12985

Re: sensor info

lol

i never actually noticed that?
katana wrote:How is it cranking at 1400 - 1600+ rpm's - most engines struggle to manage 500rpm - i've never seen a trace on these pages so flat and well defined!
by Andy-reid
Mon May 18, 2020 1:01 am
Forum: Sensors, Inputs, and Outputs
Topic: aux in / paddle setup
Replies: 15
Views: 11612

Re: aux in / paddle setup

the bit about keeping the aux in and out i found in the dta forum but the bit i copied and pasted come from the DTA tech Quickie moving from s60 to s100 paddle shift
i will ring alex today and bombard him!
by Andy-reid
Sun May 17, 2020 1:56 pm
Forum: Sensors, Inputs, and Outputs
Topic: aux in / paddle setup
Replies: 15
Views: 11612

Re: aux in / paddle setup

This is where I goy it from ans someone said on a forum to keep the input and output numerical the same for ease. If you are using a pneumatic paddle shift system, wire the relay coil for the compressor motor to one of the Aux outputs (e.g. Aux 6) and wire the tank pressure sensor to one of the anal...
by Andy-reid
Sun May 17, 2020 11:22 am
Forum: Sensors, Inputs, and Outputs
Topic: aux in / paddle setup
Replies: 15
Views: 11612

Re: aux in / paddle setup

the literature says aux6 output to run compressor relay which pin or does it not matter to aux6 input for the pressure sensor also is that just described as analog voltage in the can stream?