Search found 58 matches
- Sun Sep 11, 2022 6:45 am
- Forum: General
- Topic: Flat shift and paddle shift
- Replies: 4
- Views: 4934
Re: Flat shift and paddle shift
so a flat shift switch will still work even if it is also the paddle up? input so both systems work?
- Sun Apr 17, 2022 6:12 am
- Forum: General
- Topic: S100 paddle, launch and traction questions
- Replies: 17
- Views: 17135
Re: S100 paddle, launch and traction questions
can the values be inverted in the dta software?
- Sun Apr 17, 2022 5:29 am
- Forum: General
- Topic: S100 paddle, launch and traction questions
- Replies: 17
- Views: 17135
Re: S100 paddle, launch and traction questions
new problem i had the car at rolling road for a quick tidy up on my s100 with latest firmware my problem is i have an AEM cd7 dash with gear display all set was ok until i got car back from rollers he did say the raw voltage for the gearbox pot is wrong and my display in the AEM is all wrong but my ...
- Thu Sep 24, 2020 6:44 pm
- Forum: Sensors, Inputs, and Outputs
- Topic: aux in / paddle setup
- Replies: 15
- Views: 11830
Re: aux in / paddle setup
Quick update! the Flappy paddle setup is awesome! it almosts sounds like an auto from front and just a quick pop at the rear takes about 0.2 of a second to shift gear and power restored! nor a single missed gear! flat shift is un believable blip on down needs a bit dialing as it is a bit jerky! just...
- Thu Sep 24, 2020 6:32 pm
- Forum: General
- Topic: S100 road speed
- Replies: 1
- Views: 2839
S100 road speed
Hi! on my S100 when testing at a race track testing the Flappy paddle setup i noticed no speed displayed on my dash! for some reason the ecu is not seeing the omron proximity sensor on the diag setup?the sensor lights up when the target tooth is in place the question is can i make the ecu use my un ...
- Sun May 24, 2020 4:32 pm
- Forum: Sensors, Inputs, and Outputs
- Topic: aux in / paddle setup
- Replies: 15
- Views: 11830
Re: aux in / paddle setup
Well. Actuator fitted and valve plumbed and tested. It seems to be on down shift it blips and does an ignition cut if that is possible ? As I get a pop from the exhaust too I am awaiting a spring return blipped so I only need 1 pipe to engine bay as everything I'd under the dash
- Mon May 18, 2020 3:42 am
- Forum: Sensors, Inputs, and Outputs
- Topic: sensor info
- Replies: 17
- Views: 13188
Re: sensor info
lol
i never actually noticed that?
i never actually noticed that?
katana wrote:How is it cranking at 1400 - 1600+ rpm's - most engines struggle to manage 500rpm - i've never seen a trace on these pages so flat and well defined!
- Mon May 18, 2020 1:01 am
- Forum: Sensors, Inputs, and Outputs
- Topic: aux in / paddle setup
- Replies: 15
- Views: 11830
Re: aux in / paddle setup
the bit about keeping the aux in and out i found in the dta forum but the bit i copied and pasted come from the DTA tech Quickie moving from s60 to s100 paddle shift
i will ring alex today and bombard him!
i will ring alex today and bombard him!
- Sun May 17, 2020 1:56 pm
- Forum: Sensors, Inputs, and Outputs
- Topic: aux in / paddle setup
- Replies: 15
- Views: 11830
Re: aux in / paddle setup
This is where I goy it from ans someone said on a forum to keep the input and output numerical the same for ease. If you are using a pneumatic paddle shift system, wire the relay coil for the compressor motor to one of the Aux outputs (e.g. Aux 6) and wire the tank pressure sensor to one of the anal...
- Sun May 17, 2020 11:22 am
- Forum: Sensors, Inputs, and Outputs
- Topic: aux in / paddle setup
- Replies: 15
- Views: 11830
Re: aux in / paddle setup
the literature says aux6 output to run compressor relay which pin or does it not matter to aux6 input for the pressure sensor also is that just described as analog voltage in the can stream?